Robot gift store
  • Led light-up ladybug diy kit - handmade electronic project for beginners (soldering kit)
  • Led light-up ladybug diy kit - handmade electronic project for beginners (soldering kit)
  • Led light-up ladybug diy kit - handmade electronic project for beginners (soldering kit)
  • Led light-up ladybug diy kit - handmade electronic project for beginners (soldering kit)
  • Led light-up ladybug diy kit - handmade electronic project for beginners (soldering kit)
  • Led light-up ladybug diy kit - handmade electronic project for beginners (soldering kit)
  • Led light-up ladybug diy kit - handmade electronic project for beginners (soldering kit)
  • Led light-up ladybug diy kit - handmade electronic project for beginners (soldering kit)
  • Led light-up ladybug diy kit - handmade electronic project for beginners (soldering kit)
  • Led light-up ladybug diy kit - handmade electronic project for beginners (soldering kit)

Led light-up ladybug diy kit - handmade electronic project for beginners (soldering kit)

LED Light-Up Ladybug DIY Kit is a beginner-friendly soldering project that teaches basic electronics, circuit assembly, and STEM skills through hands-on building.

Color classification:
Parts
Loose parts + button cell battery
Loose parts + button cell battery (dz)

USD 1.99

contact shop

Product Description

Electronic Project Kit / Soldering Practice

For aesthetic reasons, the thermistor leads were not left long; however, for the actual installation, you must follow the tutorial and leave the leads at the required length.

Once the "weevil's" eyes have been soldered in place, we can test the functionality of the circuit board.

· Insert a 20mm coin cell into the battery holder with the positive side facing up.

· The LED will light up when the photoresistor detects low light levels.

· The buzzer will sound when the thermistor detects an increase in temperature.

Circuit Schematic


Product Detail Notes

1. The PCB features silkscreen markings for various components; please refer to these markings when soldering.

2. Resistors are non-polarized (direction-independent), but they have different resistance values; ensure you distinguish between them during soldering.

3. For polarized components with leads, the longer lead is positive (+) and the shorter lead is negative (-). Ensure they are oriented according to the silkscreen markings on the PCB.

4. When connecting power wires to the terminal block, be careful to distinguish between the positive and negative terminals; do not reverse the polarity.

5. Follow this soldering sequence: from the lowest profile to the highest, from the smallest components to the largest, and from the center outward.

6. Set your soldering iron to a temperature between 320°C and 380°C. Apply heat for approximately 3–5 seconds; do not solder for too long, as this may damage the circuit board's traces (ground lines).

7. On the circuit board, "VCC" indicates the positive terminal, and "GND" indicates the negative terminal.

8. Be mindful of static electricity and the power supply voltage to avoid damaging the circuit or its components.

Product parameters

Product Name :

Weevil DIY Kit

Circuit Board Dimensions :

62mm × 58mm

Supply Voltage :

3V DC power supply



Packing List

Weevil DIY Kit Packing List

Component Name

Product pictures

Parameters

PCB Marking

Quantity

Resistor


220 (Red, Red, Brown, Gold)

220

3

Thermistor


47K (Yellow, Violet, Orange, Gold)

47K

1

Electrolytic capacitor




1

Photoresistor


1UF/50V


1

Active buzzer




1

S8050 transistor


Active


1

LED


S8050

V1.V2

2

Coin cell battery holder


5mm - Red-emitting (Red)


2

Circuit board




1

20mm coin cell battery




1


Product components

The product is shipped as individual components.


Product Showcase


Supplier Information

Company:Robots gift store

Email:[email protected]

Tel:13273966089

Recommended products

Mbot Smart Car Maker Education Kit, Programmable Line-Following Robot, Arduino Compatible

A line-following educational robot kit based on the LegoDuino Pro UNO (Arduino compatible), with line sensor, ultrasonic, IR remote, fan and voice broadcast modules for line tracki

collect:0

micro:bit 3-in-1 Robot Car Kit, Scratch Programmable Building Blocks STEM Toy for Kids

A micro:bit 3-in-1 competition car built around the micro:bit expansion: LEGO-style building blocks plus Scratch graphical programming, with APP remote control.

collect:0

Guessing Dice Game Kit, Fun Electronic Dice PCB Soldering Practice DIY Kit

NE555 + CD4017 electronic dice soldering kit: 7 LEDs roll from 1 to 6, five LED colours available. A DIY soldering practice kit for beginners and hobbyists.

collect:0

Raspberry Pi Pico 2 RP2350 Dual-Core Microcontroller Board, Official Pico 2nd Generation Dev Board

Official Raspberry Pi Pico 2 board: RP2350 dual-core dual-architecture at 150MHz, 520KB SRAM, 4MB flash and 26 GPIO pins in a compact castellated form factor.

collect:0